Cadence Flash F100-5 Guide d'installation

3 CHANNEL MIXED MONO10LEFT SPEAKER4 OHMRIGHT SPEAKER4 OHMSUBWOOFERMINIMUM IMPEDANCE4-8 OHMSLOW PASS FILTER INDUCTORHIGH PASS FILTER CAPA CITORSCROSSOV

2 CHANNEL AMP BRIDGED MONO11When bridging Cadence two channel ampliers, the lowest impedance for the bridged channel is 4 ohms. Set the cro

4 CHANNEL AMP WITH 2 CHANNEL INPUT12If your head unit has only one pair of Left and Right RCA out put jacks, plug them in to RCA input Jacks 1 and 2

4 CHANNEL AMPLIFIER WITH 4 CHANNEL INPUT13If your head unit has 2 pairs of RCA output jacks, input Front Left and Front Right in to Channels 1 and 2.

BAsIC FOUR CHANNEL CONFIGURATION14FRONT SPEAKERSREAR SPEAKERSRIGHT SPEAKER2-4 OHMLEFT SPEAKER2-4 OHMLEFT SPEAKER2-4 OHMRIGHT SPEAKER2-4 OHMInstall an

4 CHANNEL AMPLIFER BRIDGED TO 2 CHANNELS15When bridging the four channel amplier, make sure that your nal woofer impedance on each bridged channel i

4 CHANNEL AMPLIFIER IN 3 CHANNEL MODE16SUBWOOFERMINIMUM IMPEDANCE4 OHMSREMOTE SUBWOOFERLEVEL CONTROLCH 1-2 CROSSOVER MODE SWITCH IN HIGH PASS POSITION

4 CHANNEL WITH MIXED MONO17REMOTE SUBWOOFERLEVEL CONTROLCH 1-2 CROSSOVER MODE SWITCH IN FULL RANGE POSITIONCH 3-4 CROSSOVER MODE SWITCH IN LOW PASS

LOW PASS FILT ER INDUCTORRIGHT SPEAKERMINIMUM SPEAKER IMPEDANCE 4 OHMSFRONT SPEAKERSREAR SPEAKERSLEFT SPEAKER4 OHMLEFT SPEAKERHIGH PASS FILTER CAPACIT

FIVE CHANNEL INPUT MODE19INPUT MODESWITCH SET TO 2CH2 CHANNEL MODE4 CHANNEL MODE5 CHANNEL MODEINPUT MODESWITCH SET TO 4CHINPUT MODESWITCH SET TO 5CHIf

INTRODUCTION2INTRODUCTION2Thank you for purchasing this Cadence Flash Series amplier. Over the years, the technology used to create audio ampliers h

5 CHANNEL AMPLIFIER SPEAKER WIRING20SUBWOOFERMINIMUM IMPEDANCE2-4 OHMSCOMPONENT SPEAKERSMINIMUM IMPEDANCE2-4 OHMSCOMPONENT SPEAKERSMINIMUM IMPEDANCE2-

- OR -DVC 4 OHM SUBWOOFERIN PARALLEL = 2 OHM LOAD2 OHM MINIMUM LOAD4 OHM SUBWOOFER 4 OHM SUBWOOFERMONO BLOCK 2 OHM AMPLIFIERSF500-1 / F700-121Both

CLASS D MONO BLOCK 1 OHM AMPLIFIER22GNDThe F1200-1D is a 1 ohm stable mono block amplier. It features RCA pre amp line output for feeding of a full r

- OR -DVC 2 OHM SUBWOOFERIN PARALLEL = 1 OHM LOAD1 OHM MINIMUM LOAD2 OHM SUBWOOFER 2 OHM SUBWOOFERF1200-1D SPEAKER CONFIGURATION23Model F1200-1D is a

F1200-1d TWIN AMPLFIER BRIDGING24GNDGNDMASTERSLAVEMASTER / SLAVE LINKSWITCH SET TO MASTERSWITCH SET TO SLAV EREMOTE SUBWOOFERLEVEL CONTROL

F1200-1d TWIN AMPLFIER BRIDGING25Two F1200-1D can be ridged together for double the power output into a 2-ohm load. Though each amp is 1 ohm stable, w

F1200-1d TWIN AMPLFIER BRIDGING26IMPORTANT NOTE:CONNECT THE TWO SPEAKER NEGATIVESTOGETHER WITH A #12 WIRE STRAP.SUBWOOFERMINIMUM IMPEDANCE2 OHMS

F1200-1d TWIN AMPLFIER BRIDGING27Once again, when bridging two ampliers together, the nal impedance load of the bridged ampliers should be no lower

SPECIFICATIONS28F500-1• Rated Power: 350 Watts RMS @ 4 ohm• Rated Power: 500 Watts RMS @ 2 ohm / 1000 Watts Peak Power• Minimum THD at Rated Power

SPECIFICATIONS29F300-2• Rated Power: 125 Watts RMS @ 4 ohm• Rated Power: 175 Watts RMS @ 2 ohm• Bridged Power: 350 Watts @ 4 ohm RMS Mono / 700 W

FEATURES3FEATURES3GOLD PLATED TERMINALS:All the terminals on the amplier are solid brass and gold plated for high conductivity and minimum impedance

SPEAKER WIRING CHART302 OHMTO AMPLIFIER4 + 4OHM4 + 4OHM4 + 4OHM4 + 4OHM4 X DUAL VC 8 OHM SPEAKERS WITH SERIES VOICE COILS, ALL IN PARALLELSERIES:SINGL

SPEAKER WIRING CHART312 X DUAL VC 2 OHM SPEAKERS WITH SERIES VOICE COILS, ALL IN PARALLELSERIES:DUAL VOICE COIL SPEAKERSPARALLEL:DUAL VOICE COIL SPEAK

Due to constant product improvements, these specifications are subject to change without notice.Though we tried our best to insure that this manual is

FEATURES“ARVA” - AUTOMATIC RAIL VOLTAGE ADJUSTMENT CIRCUITRY:Cadence Flash Series amplifiers feature “ARVA” circuitry in their power supply. This c

INSTALLATION BASICS5SETTING THE CONTROLS:AUDIO PREAMP INPUT The Flash Series ampliers feature RCA pre amp inputs. Run RCA cables from your sound sour

INSTALLATION BASICS6ADJUSTING THE SYSTEM Once the system is operational, the rst thing to do, is set all crossover points to approximate

MOUNTING AND WIRING7MOUNTING THE AMPLIFIERS:Choose a convenient mounting location with unobstructed airow.The Flash ampliers feature four mounting t

OEM RADIO INTEGRATION WITH AUTOSTART 8This newest series of Flash ampliers features our newest circuitry innovation. Say for example you

2 CHANNEL AMP WIRING9LEFT SPEAKER2-4 OHMCROSSOVER MODE SWITCH INFULL RANGE POSITION2 OHM MINIMUMPER CHANNEL STEREOCROSSOVER SWITCH SETTINGRIGHT SPEAKE